do not scale from this print .012 sq ref (typ) 0.30 .059 1.49 ref s no. of pos x .03937[1.000] .010[.25] .125 ref 3.18 .03937 ref 1.0000 .020 ref 0.50 01 02 99 100 ftmh-xx-d c2 .102 .010 2.59 0.25 .190 .010 4.83 0.25 (see note 4) "a" 'a' position t-1s16-01-xx-2 (pin 1) t-1s16-01-xx-2 (pin 2) c1 .004[.10] 05 to 25 .006[.15] 26 to 50 .015 0.38 .102 2.59 r .015 0.38 (4 plcs) .025 min flat 0.63 .010 0.25 min flat .003 0.08 max (see note 7) detail 'a' scale 6 : 1 ftmh-1xx-xx-xx-dh-x-xx no of positions -05 thru -50 ( per row) lead style spec -03: .065 post (use t-1s16-01-x-2) -02: .075 post ( use t-1s16-01-x-2) plating spec -l: light selective, 10 au / 50 ni min on contact, matte tin tail -f: flash selective, 3 au / 50 ni min on contact, matte tin tail -h: heavy gold, 30 au / 50 ni min on contact, 3 au / 50 ni min on tail -lm: light selective, 10 au / 50 ni min on contact, matte tin tail -fm: flash selective, 3 au / 50 ni min on contact, matte tin tail option 1 -k: polyimide film pad (-05 thru -50 positions only) row specification -dh: double horizontal (use ftmh-75-d) option 2 -tr: tape & reel packaging tube: pt-ftmh001-dh plug: tp-24 packaging view style -02 & -03 .105 .005 2.67 0.13 (see note 5) in-process 1 .224 .005 5.69 0.13 (see note 5) in-process 2 .131 3.31 .098 2.49 .020 .010 0.50 0.25 "p" "m" -k option polyimide film pad (available on -05 thru -50 pos only) t & r view round holes pin 01 oblong holes unwinding direction c note: "m" = use measured dimension (ref) "p" = (( "m" - .098 [2.50]) / 2) .020 [.51]) s s s table 1 lead style "a" -02 .075 [1.91] -03 .065 [1.65] sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .x: .1[2.5] .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] 1mm x 1mm horizontal smt terminal strip by: ftmh-1xx-xx-xx-dh-x-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. purvis 10/13/1998 1 1 sheet scale: 1:1 f:\dwg\misc\mktg\ftmh-1xx-xx-xx-dh-x-xx -mkt.slddrw material: body: lcp, ul 94 vo, color: black terminal: phos bronze, 510 notes: 1. represents a critical dimension. 2. max. cut flash: .015[.38]; no flash allowed in or around surface mount tail area. 3. minimum pushout force: 1 lb. 4. max. pin variance : .005[.13]. 5. shear tails to dimension shown, .003 [.08] max burr. 6. coplanarity to be within .004 when at position 05-25 and be within .006 when at position 26-50. 7. pins 1 and 2 to be flush to .0030 above line made by the body. 8. endwall to be .008 min. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision s
|
